ARUBA AP-207 change to IAP
1. proginv system ccode CCODE-RW-de6fdb363ff04c13ee261ec04fbb01bdd482d1cd //关键步骤1
2. invent -w //关键步骤2
3. dhcp //为当前设备获取ip， 或者你用setenv ip 之类的来静态指定也行
4. setenv serverip 192.168.31.112 //指定步骤二里面的哪个tftp地址
clear os 0 clear os 1
5. upgrade os 0 ArubaInstant_Cassiopeia_6.4.4.8-4.2.4.3_56707
6. upgrade os 1 ArubaInstant_Cassiopeia_6.4.4.8-4.2.4.3_56707 //5,6分别为分区0，分区1 写入上面tftp上面的固件文件，写两个确保无论哪个分区启动都是IAP，而不会跑到AP上
7.factory_reset //这个可有可无，看情况
8. saveenv //保存配置，之后重启，这样的过程就不会出现持续 turn off mobility之类的输出了
9. 链接SETUPxxxx改密码 系统里面转换独立模式 保存 重启
---------------------------------------------------
Full boot log:
Model: AP-207
CPU: BCM47452 revision: 3
Clock: 900 MHz, DDR rate: 533 MHz
DRAM: 255 MiB
Flash: Detected W25Q32FV: total 4 MiB
NAND: Detected a Mxic NAND flash: total 128 MiB
PCIe0: RC, link up
dev fn venID devID class rev MBAR0 MBAR1 MBAR2 MBAR3
00 00 14e4 aa31 00002 02 00000004 00000000 00000004 00000000
Power: DC
Net: eth0
Radio: bcm43570#0, bcm47452#1
Reset: warm
FIPS: passed
Hit <Enter> to stop autoboot: 0
Checking image @ 0x0
Copying image from 0x04100000
Image is signed; verifying checksum... passed
SHA2 Signature available
Signer Cert OK
Policy Cert OK
RSA signature verified using SHA2.
Uncompressing... done
[ 0.000000]
[ 0.000000] Aruba Networks
[ 0.000000] ArubaOS Version 8.6.0.17-8.6.0.17 (build 83573 / label #83573)
[ 0.000000] Built by p4build@pr-hpn-build07 on 2022-03-16 at 05:59:22 UTC (gcc version 4.7.2)
[ 0.000000]
[ 0.000000] Flash variant: default
[ 0.000000] MPCORE found at 18310000, SCTLR 0x10c53c7f ACTLR 0x00006040 CPSR 0x600001d3 SPSR 0x000001d3 PRRR 0xff0a81a8 NMRR 0x40e040e0
[ 0.000000] Memory: 256MB = 256MB total
[ 0.000000] Memory: 234172k/234172k available, 27972k reserved, 0K highmem
[ 0.000000] External imprecise Data abort at addr=0x76530, fsr=0xc06 ignored.
[ 0.000000] Found ST compatible serial flash with 64 64KB blocks; total size 4MB
[ 0.000000] MPCORE Global Timer Clock 33963Hz
[ 0.000000] Init timer issue new workaround, HZ 500, ticks per jiffy 68
[ 0.044000] CCA UART Clock Config: Sel=1 Ovr=1 Div=88
[ 0.044000] CCA UART Clock rate 40000000Hz
[ 0.046000] ACP (Accelerator Coherence Port) disabled
[ 12.836000] PCI: no core
[ 12.836000] PCI: no core
[ 13.038000] PCI: scanning bus 0
[ 13.038000] PCI: Fixing up bus 0
[ 13.292000] PCIE1 link=1
[ 13.292000] PCIE1 switching to GEN2
[ 13.542000] PCIE1 link=1
[ 13.542000] PCI: Fixing up bus 0
[ 13.544000] PCI: Fixing up bus 1
[ 13.544000] pci 0001:00:00.0: BAR 8: assigned [mem 0x10000000-0x105fffff]
[ 13.544000] pci 0001:01:00.0: BAR 2: assigned [mem 0x10000000-0x103fffff 64bit]
[ 13.544000] pci 0001:01:00.0: BAR 2: set to [mem 0x10000000-0x103fffff 64bit] (PCI address [0x10000000-0x103fffff]
[ 13.544000] pci 0001:01:00.0: BAR 0: assigned [mem 0x10400000-0x10407fff 64bit]
[ 13.544000] pci 0001:01:00.0: BAR 0: set to [mem 0x10400000-0x10407fff 64bit] (PCI address [0x10400000-0x10407fff]
[ 13.602000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 13.716000] Creating 1 MTD partitions on "bcmsflash":
[ 13.718000] 0x000000000000-0x000000400000 : "nor"
[ 13.720000] Northstar brcmnand NAND Flash Controller driver, Version 0.1 (c) Broadcom Inc. 2012
[ 13.722000] NAND device: Manufacturer ID: 0xc2, Chip ID: 0xf1 (MXIC NAND 128MiB 3,3V 8-bit)
[ 13.724000] Scanning device for bad blocks
[ 13.930000] Bad eraseblock 472 at 0x000003b00000
[ 14.170000] Creating 3 MTD partitions on "brcmnand":
[ 14.172000] 0x000000000000-0x000002000000 : "aos0"
[ 14.174000] 0x000002000000-0x000004000000 : "aos1"
[ 14.176000] 0x000004000000-0x000008000000 : "ubifs"
[ 15.536000] i2c-springbank: using remapped base d09d0060
[ 15.538000] mpcore_wdt mpcore_wdt: enabling watchdog.
[ 15.540000] ramzswap: num_devices not specified. Using default: 1
[ 15.542000] ramzswap: Creating 1 devices ...
[ 15.548000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[ 15.550000] All bugs added by David S. Miller <davem@redhat.com>
[ 15.668000]
[ 15.668000] Starting Kernel SHA1 KAT ...Completed Kernel SHA1 KAT
[ 15.672000] Starting Kernel HMAC-SHA1 KAT ...Completed Kernel HMAC-SHA1 KAT
[ 15.706000] Starting Kernel DES KAT ...Completed Kernel DES KAT
[ 15.710000] Starting Kernel AES KAT ...Completed Kernel AES KAT
[ 15.712000]
[ 15.714000] Starting Kernel AESGCM KAT ...Completed Kernel AESGCM KAT
grep: /tmp/ap-info: No such file or directory
Thu Jan 1 00:00:00 PST 1970
Populate AP type info
Domain Name: SetMeUp.arubanetworks.com
Current OEM Name : Aruba Networks
Disabling ipv6 for devices by default
[ 17.706000] ramzswap: Disk size set to 182272 kB
[ 17.708000] ramzswap: Device already initialized!
[ 17.718000] Adding 182268k swap on /dev/ramzswap0. Priority:-1 extents:1 across:182268k SS
AP-type has_ble_support: BRCM_ONBOARD.
IPv6 capability is supported for devices
No panic info available
Enabling bsa_server via nanny
Enabling ble_daemon and ble_relay via nanny
springbank: Start hotplug
Backup ENV.
Enter non-FIPS mode
Cfg len is 2928
factory default SSID detected...
factory_ssid_present 1
standalone mode in non-fips mode
Mesh disabled
Starting watchdog process...
dual_uplink_default is 0
Loading configuration file of length 2928...
wifi uplink not present...
extended ssid config detected...
Terminal access enabled...
factory default SSID detected...
No valid ssid was found...
extended ssid activate due to no valid ssid ...
touching file /tmp/ip_mode_0
[ 44.960000] ADDRCONF(NETDEV_UP): bond0: link is not ready
do ethtool autoneg on for bond0
eth1 admin down
SIOCGIFFLAGS: No such device
init usb modem ...
springbank: Copying BT modules to /tmp
USB is not supported on this model
Ethernet uplink eth0 not active yet
[ 47.966000] bond0: link up (100FD)
[ 47.968000] ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
skip backup uplink detect, as preferred uplink is UP
set eth0 as select uplink
disable auto topology rules
Starting up in standalone mode
extended ssid is activated on the platform ...
copying bootuplog ...
[ 49.114000] UOL ctf init done
[ 49.116000] uol_init_driver:409 HW offload not applicable, AP will use cutting through path!
[ 49.118000] init_uol_mod: offload cap: 0x40, mesh mode none, strapless_enabled 0, uplink_vlan 0
[ 49.872000] AP xml model 96, num_radios 2 (jiffies 24936)
[ 49.874000] apType 96 hw_opmode 0
[ 49.876000] radio 0: band 1 ant 0 max_ssid 16
[ 49.878000] radio 1: band 0 ant 0 max_ssid 16
[ 49.880000] init_asap_mod: installation:0
[ 49.882000] election init: rand=12 HZ=500
[ 49.884000] IAP client match init
set device anul0 mtu to 2000
notify asap_mod 3g no present...
notify asap standalone ap...
apdot1x authentication is not enabled
LLDP not sent yet, DHCP is waiting
LLDP not sent yet, DHCP is waiting
Starting DHCP
Getting an IP address...
Jan 1 00:00:39 udhcpc[3381]: udhcpc (v0.9.9-pre) started
Jan 1 00:00:39 udhcpc[3381]: send_discover: pkt num 0, secs 0
Jan 1 00:00:39 udhcpc[3381]: Sending discover...
Jan 1 00:00:40 udhcpc[3381]: send_selecting: pkt num 0, secs 0
Jan 1 00:00:40 udhcpc[3381]: Sending select for 9.32.2.1...
Jan 1 00:00:40 udhcpc[3381]: Lease of 9.32.2.1 obtained, lease time 180
[ 54.896000] ip_time_handler: Got ip and packets on bond0 Started master election 2-0, rand 15
9.32.2.1 255.255.0.0 9.32.2.22
Compressing all files in the /etc/httpd directory...
Done.
Starting Webserver
bind: Transport endpoint is not connected
bind: Transport endpoint is not connected
bind: Transport endpoint is not connected
Put ntpdate to the nannylist.
[ 69.470000] vmap allocation for size 8245248 failed: use vmalloc=<size> to increase size.
[ 70.236000] wifi0: AP type AP-207, radio 0, max_bssids 16
[ 70.484000] PCI: Enabling device 0001:01:00.0 (0140 -> 0142)
[ 70.686000] wifi1: AP type AP-207, radio 1, max_bssids 16
springbank: Insmod BT modules
[ 71.712000] usbcore: registered new interface driver usbfs
[ 71.726000] usbcore: registered new interface driver hub
[ 71.746000] usbcore: registered new device driver usb
[ 71.868000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 71.872000] ehci_hcd 0000:00:04.1: EHCI Host Controller
[ 71.874000] ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
[ 71.928000] ehci_hcd 0000:00:04.1: irq 36, io mem 0x18004000
[ 71.944000] ehci_hcd 0000:00:04.1: USB 0.0 started, EHCI 1.00
[ 71.946000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 71.948000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 71.950000] usb usb1: Product: EHCI Host Controller
[ 71.952000] usb usb1: Manufacturer: Linux 2.6.35 ehci_hcd
[ 71.954000] usb usb1: SerialNumber: 0000:00:04.1
[ 72.060000] hub 1-0:1.0: USB hub found
[ 72.062000] hub 1-0:1.0: 2 ports detected
[ 72.268000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 72.270000] ohci_hcd 0000:00:04.0: OHCI Host Controller
[ 72.272000] ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 2
[ 72.274000] ohci_hcd 0000:00:04.0: irq 36, io mem 0x1800d000
[ 72.356000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 72.358000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 72.360000] usb usb2: Product: OHCI Host Controller
[ 72.362000] usb usb2: Manufacturer: Linux 2.6.35 ohci_hcd
[ 72.364000] usb usb2: SerialNumber: 0000:00:04.0
[ 72.544000] hub 2-0:1.0: USB hub found
[ 72.546000] hub 2-0:1.0: 2 ports detected
[ 72.856000] usbcore: registered new interface driver btusb
[ 72.864000] usb 2-1: new full speed USB device using ohci_hcd and address 2
[ 73.014000] usb 2-1: New USB device found, idVendor=0a5c, idProduct=2045
[ 73.016000] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 73.018000] usb 2-1: Product: BCM2045A0
[ 73.020000] usb 2-1: Manufacturer: Broadcom Corp
[ 73.022000] usb 2-1: SerialNumber: 000000000000
AP rebooted Wed Mar 16 06:09:37 UTC 2022; UI cmd at uptime 0D 0H 11M 44S: reload
shutting down watchdog process (nanny will restart it)...
<<<<< Welcome to the Access Point >>>>>
Completed SW FIPS KAT test
Power supply mode is DC, USB Modem is not present.
User: